NEC SigmaBlade B140a-T Guía de usuario Pagina 244
- Pagina / 376
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
8-48 Troubleshooting
The CPU blade is not found on the network:
Is the LAN cable connected?
→ Make sure to connect the LAN cable to the network port on the rear of the CPU
blade. Also make sure that the LAN cable to use conforms to the network
interface standard.
Is BIOS configuration correct?
→ The onboard LAN controller may be disabled with the BIOS SETUP utility of the
CPU blade. Check the setting with the BIOS SETUP utility.
[Advanced] – [PCI Configuration] – [Embedded NIC (Dual Gbit)] – [LAN #1
Option ROM Scan], [LAN #2 Option ROM Scan]>
Have the protocol and service already configured?
→ Install the distinctive network driver for the CPU blade. Make sure that the
protocol, such as TCP/IP, and services are properly specified.
Is the transfer speed correct?
→ Open the network property dialog box in control panel to specify the "Link Speed
& Duplex" value the same as the value specified for HUB.
The system displays the message below and fails to log in:
→ In Windows Server 2003, the following message will be displayed if you use the
operating system without executing the license authentication.
Select "Yes", and execute the procedure for license authentication.
Windows Product Activation
This copy of Windows must be activated with Microsoft before you can
continue, You cannot log on until you activate Windows.
Do you want to activate Windows now?
To shut down the computer, click Cancel.
YES NO Cancel
The Telnet Service is not installed.
Adjust the computer name to 14 characters or less, and then install the Telnet Service according to
<How to install the Telnet Service>.
<How to install the Telnet Service>
1. Click [Run] on Start menu.
2. Type "tlntsvr /service" in the [Open] box, and click [OK].
3. Click Start menu, point to [Control Panel] and click [Administrative Tools] and then click
the [Services] to verify whether the Telnet Service is registered.
* When the installation of Telnet Service is finished, there is no problem if the computer
name is set to 15 characters or more.
- NEC Express5800/B140a-T 1
- User's Guide 1
- SAFETY INDICATIONS 3
- Attentions 4
- Prohibited Actions 4
- Mandatory Action 4
- Trademarks 6
- ABOUT THIS USER'S GUIDE 8
- IN THE PACKAGE 9
- CONTENTS 10
- Chapter 1 15
- SAFETY NOTES 16
- Do not step on the cable 17
- FOR PROPER OPERATION 19
- TRANSFER TO THIRD PARTY 21
- DISPOSAL AND CONSUMABLES 22
- USER SUPPORT 23
- Advice for Health 24
- Chapter 2 25
- OVERVIEW 26
- STANDARD FEATURES 27
- PART NAMES AND CONTROLS 28
- General Description 2-5 29
- Rear View 30
- Internal View 31
- SAS Board 32
- External View 33
- Lamp Indications 35
- STATUS Lamp 36
- LAN (1 - 4) Link/Access Lamps 37
- DISK ACCESS Lamp 37
- USING YOUR SERVER 38
- Power ON from CPU Blade 39
- Operation after Power ON 39
- POST Execution Flow 41
- Power-off of Blade Server 43
- Device Identification 44
- Chapter 3 45
- BEFORE INSTALLING CPU BLADE 46
- Installing DIMM 47
- INSTALLING THE CPU BLADE 48
- MAKING CONNECTIONS 49
- Setting Up Your Server 3-7 51
- 3-8 Setting Up Your Server 52
- Blade Enclosure for details 52
- Chapter 4 53
- Starting SETUP Utility 54
- Configuration Examples 56
- Keyboard 58
- Security 59
- External Devices 59
- Internal Devices 59
- Saving the Configuration Data 59
- [ ]: Factory-set 61
- 4-10 Configuring Your Server 62
- Processor Settings 62
- Advanced 64
- Memory Configuration 65
- 4-14 Configuring Your Server 66
- PCI Configuration 66
- Onboard SAS 67
- 4-16 Configuring Your Server 68
- Onboard NIC 68
- 4-22 Configuring Your Server 74
- System Management 75
- 4-24 Configuring Your Server 76
- Console Redirection 76
- Event Log Configuration 77
- RAID SYSTEM CONFIGURATION 81
- Standby rebuild 86
- Hot-swap rebuild 86
- 4-38 Configuring Your Server 90
- Before Using WebBIOS 91
- Using WebBIOS 93
- Main Menu 94
- Adapter Properties 96
- 4-46 Configuring Your Server 98
- Scan Devices 100
- IMPORTANT: 100
- Virtual Disks 101
- Physical Drives 102
- 3. Click [Go] 103
- Adapter Selection 104
- Physical View / Logical View 104
- Configuration Wizard 104
- Configuring Virtual Disk 106
- 4-56 Configuring Your Server 108
- 4-58 Configuring Your Server 110
- 4-60 Configuring Your Server 112
- Configure SPAN 116
- 4-66 Configuring Your Server 118
- [Accept] 119
- 4-68 Configuring Your Server 120
- Operation of Various Features 123
- Manual Rebuild 125
- 1. Start WebBIOS 125
- Setting Hot Spare 127
- Reconstruction 130
- Number and ID 133
- Setting of Priority 134
- Chapter 5 137
- About Express Setup 138
- Microsoft Windows Server 2003 139
- Installing the Service Pack 143
- FLOW OF SETUP 144
- About partition size 148
- 14. Save the parameters 151
- Setup of teaming 154
- 8. Click [Install] 155
- Optional Network Board Driver 156
- Setting WOL 159
- Graphics Accelerator Driver 160
- SETTING FOR SOLVING PROBLEMS 162
- Windows Dr. Watson 165
- Network Monitor 166
- UPDATING THE SYSTEM 167
- Chapter 6 171
- NEC EXPRESSBUILDER 172
- Os installation 173
- Tool menu (Normal Mode) 174
- Autorun Menu 176
- PARAMETER FILE CREATOR 177
- Parameter File 178
- 15. Saved to a floppy disk 186
- NEC ESMPRO 188
- Universal RAID Utility 189
- NEC DianaScope 190
- Chapter 7 191
- SYSTEM DIAGNOSTICS 192
- <Device List> 195
- <Log Info> 195
- <Option> 195
- <Reboot> 195
- 7-6 Maintenance 196
- Chapter 8 197
- SYSTEM VIEWERS 198
- ERROR MESSAGES 199
- 8-4 Troubleshooting 200
- Troubleshooting 8-5 201
- 8-6 Troubleshooting 202
- Troubleshooting 8-7 203
- 8-8 Troubleshooting 204
- Troubleshooting 8-9 205
- 8-10 Troubleshooting 206
- Troubleshooting 8-11 207
- 8-12 Troubleshooting 208
- Troubleshooting 8-13 209
- 8-14 Troubleshooting 210
- Troubleshooting 8-15 211
- 8-16 Troubleshooting 212
- Troubleshooting 8-17 213
- 8-18 Troubleshooting 214
- Other POST Error 215
- Error Messages on Virtual LCD 216
- ASF Codes 217
- POST Progress Codes 217
- Other Messages 218
- Troubleshooting 8-23 219
- 8-24 Troubleshooting 220
- Troubleshooting 8-25 221
- 8-26 Troubleshooting 222
- Troubleshooting 8-27 223
- 8-28 Troubleshooting 224
- Troubleshooting 8-29 225
- 8-30 Troubleshooting 226
- Troubleshooting 8-31 227
- 8-32 Troubleshooting 228
- Troubleshooting 8-33 229
- 8-34 Troubleshooting 230
- Troubleshooting 8-35 231
- 8-36 Troubleshooting 232
- Troubleshooting 8-37 233
- 8-38 Troubleshooting 234
- Troubleshooting 8-39 235
- 8-40 Troubleshooting 236
- Troubleshooting 8-41 237
- SOLVING PROBLEMS 238
- Fail to power-off: 239
- POST fails to complete: 239
- Is the OS broken? 242
- It is not a failure 242
- Did you update the system? 243
- Problems with Windows 245
- Server 2003 x64 Editions 247
- Server 2003 R2 249
- Problems with Express Setup 251
- Is the RAID configured? 252
- Is RAID0 configured? 252
- Auto rebuild fails: 253
- A hard disk drive fails: 253
- COLLECTING EVENT LOG 254
- MEMORY DUMP 256
- RECOVERY FOR Windows SYSTEM 257
- MAINTENANCE TOOLS 258
- Function of Maintenance Tools 260
- BIOS/FW Updating 261
- ROM-DOS startup FD 261
- Test and diagnostics 261
- System Management 261
- Starting 262
- RESETTING THE CPU BLADE 264
- FORCED SHUTDOWN 264
- Chapter 9 265
- ANTI-STATIC MEASURES 267
- PREPARATION FOR INSTALLATION 268
- Processor (CPU) 269
- 9-6 Upgrading Your Server 270
- 9-8 Upgrading Your Server 272
- Upgrading Your Server 9-9 273
- 10. Lift the socket lever 274
- Upgrading Your Server 9-11 275
- Adding Order and Precautions 279
- Key slot 281
- Online Spare Memory 284
- Memory Mirroring 286
- Mezzanine Card 288
- Hard Disk Drive 293
- 9-32 Upgrading Your Server 296
- Appendix A 297
- A-2 Specifications 298
- Appendix B 299
- <Example> 300
- Setup Procedure 305
- Create from [Autorun Menu] 307
- The installation starts 311
- Install Windows – Insert Disc 314
- OK Cancel 314
- Alt + Del 316
- REMOTE DESKTOP FOR MANAGEMENT 326
- Windows Server 2003 327
- Setup of teaming 328
- Graphics Accelerator 330
- Balancing (ALB) 333
- Setup Teaming 334
- Remove Team 336
- SETTING WOL 337
- 10. Click [OK] 343
- 2. Select [Advanced] tab 344
- Local Update 354
- <Windows Server 2003> 357
- About Windows Activation 369
- 4. Activate Windows 371
Relacionado con productos y manuales para Servidores NEC SigmaBlade B140a-T
Servidores NEC Express5800/120Li Guía de usuario
(344 paginas)
(344 paginas)
Servidores NEC Express5800/1160Xd Guía de usuario
(214 paginas)
(214 paginas)
Servidores NEC Express5800/R110d-1E Guía de usuario
(133 paginas)
(133 paginas)
Servidores NEC MC2400 Manual de usuario
(204 paginas)
(204 paginas)
Servidores NEC Express5800/R120b-2 Guía de usuario
(556 paginas)
(556 paginas)
Servidores NEC Express5800/120Mc2 Guía de usuario
(172 paginas)
(172 paginas)
Servidores NEC Express5800/120Rd-2 Guía de usuario
(326 paginas)
(326 paginas)
Servidores NEC MH4500 Manual de usuario
(186 paginas)
(186 paginas)
Servidores NEC Express5800/R120f-1M Guía de usuario
(133 paginas)
(133 paginas)
Servidores NEC Express 5800/230Eh Manual de usuario
(342 paginas)
(342 paginas)
Servidores NEC Express5800/HX6100 Guía de usuario
(192 paginas)
(192 paginas)
Servidores NEC EXPRESS5800/100 Manual de usuario
(152 paginas)
(152 paginas)
Servidores NEC N8103-102 Manual de usuario
(60 paginas)
(60 paginas)
Servidores NEC Express5800/R120e-1M Guía de instalación
(267 paginas)
(267 paginas)
Servidores NEC IS016-5E Manual de usuario
(87 paginas)
(87 paginas)
Servidores NEC Express5800/R110d-1E Guía de usuario
(101 paginas)
(101 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.074 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales