NEC Express5800/GT110e-S Guía de instalación Pagina 66
- Pagina / 275
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
3. Setting Up Windows Server 2008 R2
press5800/GT-110e, GT-110e-S, R110e-1E Installation Guide (Windows)
66
Chapter 1 Installing Windows
3.5.3
Setting up team/LiveLink
Important
• When using
Smart Load Balancing and Failover (without Standby
Member ), be sure to setup LiveLink at creation of team.
When using Smart Load Balancing and Failover (with Standby Member ),
setup for LiveLink is not essential.
• When deleting the team, refer to Chapter 1 (3.5.3 Setting up team/LiveLink)
– (4) Procedure for deleting team
. When replacing the motherboard or a
LAN board, follow these steps to remove the team and then create it again
after replacement.
• Be sure to specify the same Jumbo Mtu (Jumbo Packet) setting to all the
adapters that compose a team.
• Using Server Core installations, Not supporting setting up team/LiveLink
by the BACS.
(1) Team types
The following team types are supported.
• Smart Load Balancing and Failover (without Standby Member)
All adapters that compose the team perform communication.
If a communication failure occurs on an adapter, other adapters that compose the team continue the
communication.
When the adapter on which the communication failure occurred recovers, it joins the team again and
resumes the communication.
• Smart Load Balancing (Auto-Failback Disable) (with Standby Member)
Among the adapters that compose the team, primary adapters except the standby member perform
communication.
If a communication failure occurs, the standby member continues the communication.
When the adapter on which the communication failure occurred recovers, it joints the team again and
the standby adapter returns to the standby state.
(2) LiveLink
LiveLink is a function that detects communication route failures of adapters.
It periodically investigates the communication status of specified destinations (IP address).
Link packets are sent from each adapter within a team.
If a response to the transmission of a link packet within the specified range is not detected, it is identified as a
communication route failure and adapter communication is stopped.
When a response to the submission of a link packet is detected, communication LiveLink identifies
communication as having been recovered, and communication using that adapter automatically resumes.
Note
You must set up LiveLink when you create a team.
- EXP280A, EXP281A, EXP282A 1
- Installation Guide (Windows) 1
- Contents 3
- Trademarks 8
- Regulatory Notices 9
- EEE Yönetmeliğine Uygundur 10
- Latest editions 11
- Installing Windows 12
- Before Starting Setup 13
- Supported Windows OS 14
- Service Pack Support 15
- EXPRESSBUILDER 18
- Free space 22
- System Partition (40,860 MB) 22
- Boot Partition (100 MB) 22
- Setup with EXPRESSBUILDER 23
- Setup flow 104
- Requirements for Setup 105
- Setup procedure 106
- Install Windows – Insert Disc 117
- OK Cancel 117
- Installing Starter Pack 121
- Setting Up Device Drivers 129
- Setting up LAN drivers 130
- Setting up team/LiveLink 132
- Do not use Expert Mode 134
- Graphics accelerator driver 143
- Specifying PAE Option 145
- License Authentication 147
- Applying Service Pack 150
- Data area 153
- (partition to be retained) 153
- Flash FDD on BIOS settings 165
- Important 167
- Recovery process 180
- Setup for Solving Problems 248
- For Windows Server 2008 250
- For Windows Server 2003 252
- Installing Network Monitor 256
- Windows OS Parameter File 258
- 8. Windows OS Parameter File 259
- NEC Express5800 Series 269
- NEC ESMPRO Agent Extension 271
- BMC Configuration 271
- NEC ExpressUpdate Agent 271
- Universal RAID Utility 272
- NEC ESMPRO Manager 275
Relacionado con productos y manuales para Software NEC Express5800/GT110e-S
Software NEC Express5800/R120f-1M Manual de usuario
(61 paginas)
(61 paginas)
Software NEC Express5800/120Ri-2 Guía de usuario
(64 paginas)
(64 paginas)
Software NEC N8406-022A Manual de usuario
(90 paginas)
(90 paginas)
Software NEC Express5800/GT110d-S Guía de instalación
(278 paginas)
(278 paginas)
Software NEC Express5800/R120d-2M Guía de instalación
(291 paginas)
(291 paginas)
Software NEC Express5800/320Ma Manual de usuario
(74 paginas)
(74 paginas)
Software NEC Express5800/320Fc Guía de usuario
(120 paginas)
(120 paginas)
Software NEC NDA-30122 Manual de usuario
(136 paginas)
(136 paginas)
Software NEC Express5800/R120d-2E SR Guía de usuario
(105 paginas)
(105 paginas)
Software NEC Express5800/A1160 Guía de usuario
(88 paginas)
(88 paginas)
Software NEC Express5800/320Ma Guía de usuario
(48 paginas)
(48 paginas)
Rockwell Automation 20D PowerFlex 700S and 700H Frame 10...12 Rectifie manuales
Manuales del propietario y guías del usuario para Equipo Rockwell Automation 20D PowerFlex 700S and 700H Frame 10...12 Rectifie.
Ofrecemos 1 manuales en pdf Rockwell Automation 20D PowerFlex 700S and 700H Frame 10...12 Rectifie para descargar gratis por tipos de documentos: Manual de usuario
Comentarios a estos manuales