NEC Express5800/GT110e-S Guía de instalación Pagina 201
- Pagina / 275
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
6. Setting Up Windows Server 2003
Express5800/GT-110e, GT-110e-S, R110e-1E Installation Guide (Windows)
201
Chapter 1 Installing Windows
(3/3)
Setup Items to confirm
– –
System
partition size
The system partition size can be calculated by using the following formula.
Size required to install the OS + paging file size + dump file size + application size
Size required to install the OS = 3,500 MB
(Windows Server 2003 R2 with Service Pack 2)
= 5,300 MB
(Windows Server 2003 R2 + Service Pack 2)
＝ 5300MB
(Windows Server 2003 with Service Pack 1
+ ServicePack 2 CD-ROM)
Paging file size (recommended) = installed memory size × 1.5
Dump file size = installed memory size + 12 MB
Application size = as required by the application
For example, if the installed memory size is 1 GB (1,024 MB), the partition size is calculated
as follows:
3,500 MB + (1,024 MB × 1.5) + 1,024 MB + 12 MB + application size = 6,072 MB +
application size
Note
• The above paging file sizes are recommended for collectin
g debug
information (dump file). The initial size of the boot volume paging file must be
large enough to store dump files. Make sure you set a sufficient paging file
size. If the paging file is insufficient, there will be a virtual memory shortage
that may result in an inability to collect correct debug information.
• The maximum paging file size that can be specified for one partition is 4095
MB. If 1.5 times of the mounted memory size exceeds 4095 MB, specify 4095
MB.
• If the mounted memory size is 2 GB or greater, the maximum size of the
dump file is “2048 MB + 12 MB”.
• When installing other applications or other items, add the amount of space
needed by the application to the partition.
If the partition size for installing Windows is smaller than the recommended size, expand the
partition size or add another hard disk drive.
– −
Setup with OS
standard
installer
Dialog boxes
appear several times during installation, but it does not affect system
installation. Click [Yes] on such dialog boxes, and continue installation according to the
displayed messages.
－ －
When using
RAID
Controller
(N8103-149/15
0/151/160)
Upon completion of installation of OS and application of Service Pack 2, update the driver for
RAID Controller before installing Universal RAID Utility. Take the steps below:
1. Insert the EXPRESSBUILDER DVD into optical disk drive.
2. Open the following file using text editor such as notepad.
<EXPRESSBUILDER DVD>：\024\win\winnt\dotnet\dac_driver_update\Readme.txt
3. Update the driver according to instructions in Readme.txt file.
When update completes, install the Universal RAID Utility.
－ －
Upgrade to
Windows
Server 2003 R2
Inplace upgrade from Windows Server 2003 to Windows Server 2003 R2 is not recommended
because it overwrites the files and registries and might cause an unexpected effect on the
system and applications.
If you want to use Windows Server 2003 R2, back up the necessary data before installing
Windows Server 2003 R2.
Tips
Inplace upgrade refers to overwriting an existing OS (in this case, Windows
2003) with another OS (Windows Server 2003 R2).
- EXP280A, EXP281A, EXP282A 1
- Installation Guide (Windows) 1
- Contents 3
- Trademarks 8
- Regulatory Notices 9
- EEE Yönetmeliğine Uygundur 10
- Latest editions 11
- Installing Windows 12
- Before Starting Setup 13
- Supported Windows OS 14
- Service Pack Support 15
- EXPRESSBUILDER 18
- Free space 22
- System Partition (40,860 MB) 22
- Boot Partition (100 MB) 22
- Setup with EXPRESSBUILDER 23
- Setup flow 104
- Requirements for Setup 105
- Setup procedure 106
- Install Windows – Insert Disc 117
- OK Cancel 117
- Installing Starter Pack 121
- Setting Up Device Drivers 129
- Setting up LAN drivers 130
- Setting up team/LiveLink 132
- Do not use Expert Mode 134
- Graphics accelerator driver 143
- Specifying PAE Option 145
- License Authentication 147
- Applying Service Pack 150
- Data area 153
- (partition to be retained) 153
- Flash FDD on BIOS settings 165
- Important 167
- Recovery process 180
- Setup for Solving Problems 248
- For Windows Server 2008 250
- For Windows Server 2003 252
- Installing Network Monitor 256
- Windows OS Parameter File 258
- 8. Windows OS Parameter File 259
- NEC Express5800 Series 269
- NEC ESMPRO Agent Extension 271
- BMC Configuration 271
- NEC ExpressUpdate Agent 271
- Universal RAID Utility 272
- NEC ESMPRO Manager 275
Relacionado con productos y manuales para Software NEC Express5800/GT110e-S
Software NEC Express5800/R120f-1M Manual de usuario
(61 paginas)
(61 paginas)
Software NEC Express5800/120Ri-2 Guía de usuario
(64 paginas)
(64 paginas)
Software NEC N8406-022A Manual de usuario
(90 paginas)
(90 paginas)
Software NEC Express5800/GT110d-S Guía de instalación
(278 paginas)
(278 paginas)
Software NEC Express5800/R120d-2M Guía de instalación
(291 paginas)
(291 paginas)
Software NEC Express5800/320Ma Manual de usuario
(74 paginas)
(74 paginas)
Software NEC Express5800/320Fc Guía de usuario
(120 paginas)
(120 paginas)
Software NEC NDA-30122 Manual de usuario
(136 paginas)
(136 paginas)
Software NEC Express5800/R120d-2E SR Guía de usuario
(105 paginas)
(105 paginas)
Software NEC Express5800/A1160 Guía de usuario
(88 paginas)
(88 paginas)
Software NEC Express5800/320Ma Guía de usuario
(48 paginas)
(48 paginas)
Rockwell Automation 20D PowerFlex 700S and 700H Frame 10...12 Rectifie manuales
Manuales del propietario y guías del usuario para Equipo Rockwell Automation 20D PowerFlex 700S and 700H Frame 10...12 Rectifie.
Ofrecemos 1 manuales en pdf Rockwell Automation 20D PowerFlex 700S and 700H Frame 10...12 Rectifie para descargar gratis por tipos de documentos: Manual de usuario
Comentarios a estos manuales