NEC Express5800/R120f-1M Guía de usuario Pagina 27
- Pagina / 144
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Installation (Linux, VMware ESX)
Use setup.sh in the installation image to install latest Universal RAID Utility.
You must install the Universal RAID Utility in the ESX Server. Do not install Universal RAID
Utility in the virtual machine.
Step 1
Check if the operating system recognizes all the RAID Controllers connected. Please be sure to connect all the
RAID Controllers before installing Universal RAID Utility.
The program to control the RAID Controller depends on the type of RAID Controller. Please be
sure to connect all the RAID Controllers first then install Universal RAID Utility.
Step 2
Execute setup.sh in the installation image.
Change the current directory to the directory in which the
installation image is stored and type as follows:
(In case of Linux)
sh setup.sh --install
(In case of VMware ESX)
sh setup.sh --install –reptblen
Specify
“—nomgr” instead of “—install” as an option at installation to exclude the NEC
ESMPRO Manager
Communication Module (eciservice package and raidsrv agent service).
Step 3
At the end of setup.sh, the installation is completed. Check the result of the installation by using the rpm
command. When the installation is completed properly, the following packages are installed:
- UniversalRAIDUtility-x.yy-z (x is major version, yy is minor version, z is release number for x.yy)
- eciservice-a.bb-x.i386 (a is major version, bb is minor version)
(eciservice package and raidsrv agent service are not installed when you specify the –nomgr option at setup.)
Also, the programs to manage the RAID Controllers will be installed with any one of the following combinations depending
on the type of the RAID Controller used in your system.
- storelib-a.bb-0 (a.bb is version)
- WebPAMPRO_Agent-3.aa.bbbb-cc (aa.bbbb-cc is version)
- storelib-a.bb-0 (a.bb is version) and WebPAMPRO_Agent-3.aa.bbbb-cc (aa.bbbb-cc is version)
If the installation fails, these packages do not exist in the computer.
Universal RAID Utility does not install the following packages in the VMware ESX environment.
Please note that the installation is finished successfully in VMware ESX
even after the
program d
oes not exist.
storelib-a.bb-0. (a.bb is version)
NEC ESMPRO Manager Ver5.5 or later versions is required to manage the server where
Universal RAID Utility Ver
4.0 has been installed.
See “
Installation of NEC ESMPRO Manager” for details.
> cd
directory name involved installation image
> sh setup.sh --install
>
> rpm -q UniversalRaidUtility
UniversalRaidUtility-x.yy-z
>
> rpm –q eciservice-a.bb-x.i386
eciservice-a.bb-x.i386
>
> rpm -q storelib
storelib-a.bb-0
>
> rpm -q WebPAMPRO_Agent
WebPAMPRO_Agent-3.aa.bbbb-cc
>
2
3
27
- Universal RAID Utility 1
- User's Guide 1
- Introduction 4
- Contents 5
- Overview 10
- Windows Server 11
- Linux/VMware ESX 11
- Management PC 11
- System requirements 13
- Software (Linux) 14
- Software (VMware ESX) 14
- Resources 15
- Installation image 17
- Installation (Windows) 20
- Uninstallation (Windows) 23
- Log Viewer 32
- Standard and Advanced Modes 34
- Functions of RAID Viewer 36
- Battery 38
- Flash Backup Unit 38
- Disk Array 38
- SSD Cache Disk Array 39
- SSD Cache Drive 40
- Shortcut Menu 41
- Operation View 42
- Menu Bar 43
- [OFF] goes off the lamp 45
- Status Bar 46
- Functions of Log Viewer 47
- Log View 48
- Functions of raidcmd 50
- RAID System Configuration 51
- Configuration of RAID System 63
- Making Hot Spare 64
- About Dedicated Hot Spare 65
- Making Global Hot Spare 66
- Making Dedicated Hot Spare 67
- Removing Hot Spare 68
- Capacity of Logical Drive 75
- Items set for Logical Drive 75
- Number of Hot Spares 76
- Modes of Hot Spares 77
- Mode" 78
- Deleting Logical Drive 86
- Using CacheCade 87
- Capacity of SSD Cache Drive 89
- Deleting SSD Cache Drive 90
- Maintenance of RAID System 91
- Setting Patrol Read Priority 92
- Enabled) 93
- Disabled) 94
- Stopping Consistency Check 96
- Initializing Logical Drive 98
- Stopping Initialize 99
- Setting Initialize Priority 100
- Setting cache mode 101
- Rebuilding Physical Device 102
- Stopping Rebuild 103
- Setting Rebuild Priority 104
- Setting Power Saving Devices 105
- Setting Device Standby Time 106
- RAID Viewer 108
- To Online Forcibly 109
- To Failed Forcibly 110
- Step 1 Execute " 111
- Step 3 If " 111
- Scheduling Refresh Battery 113
- Troubleshooting RAID System 115
- Failure Detection Measures 116
- Windows 117
- Buzzer in RAID Controller 118
- Logical drive 121
- Physical device 121
- Physical device (Hot Spare) 121
- [Symbols] 121
- Physical Device 122
- [Online] 122
- Logical Drive 122
- Monitoring Battery Status 126
- Monitoring Enclosure Status 128
- Tree View of RAID Viewer 131
- Property of RAID Viewer 131
- Property of raidcmd 131
- ESMPRO Manager 132
- Using ExpressUpdate 135
- Utility 136
- Avoiding TCP port conflict 137
- Operation Environment 139
- OS Fatal Error Event 140
- RAID Viewer, Log Viewer 141
- Log Rotation 142
- NEC ESMPRO Manager 143
- RAID Controller 143
- Consistency Check 143
Relacionado con productos y manuales para Los controladores raid NEC Express5800/R120f-1M
Los controladores raid NEC N8103-89 Manual de usuario
(128 paginas)
(128 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.089 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales