NEC Express5800/R120f-1M Guía de usuario Pagina 114
- Pagina / 144
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Updating firmware of the RAID Controller
The Update firmware of the RAID Controller is a function to update the firmware of the RAID Controller.
The function of update firmware of the RAID Controller are available with
N8103-176/177/178/179 RAID Controller.
Do not stop raidsrv service (including restart), abort raidcmd and stop system (including
restart) when updating the firmware of the RAID Controller.
Executing Update Firmware Of The RAID Controller
The procedure of executing update firmware of the RAID Controller is described below.
The update firmware of the RAID Controller is available only in the Advanced Mode.
RAID Viewer
The update firmware of the RAID Controller can use only raidcmd.
raidcmd
Step 1 After downloading firmware of the RAID controller you use, extract to the arbitrary place.
The
firmware of the RAID Controller is released on the “NEC Global Site”
(
http://www.nec.com/).
However, the firmware of the RAID Controller you use is not released on "NEC Global Site" if it
is not updating.
Step 2 Execute "
fwup
" command using the
following parameter.
-c
: Number of RAID Controller for which update firmware.
-f
: Absolute path of stored area of the firmware file of the
RAID Controller.
-ocr
: Specify whether the RAID Controller is reset on-line after updating firmware of the RAID Controller or not. Specify "yes" if
resetting the RAID Controller. Specify "no" if not resetting the RAID Controller. If not resetting RAID Controller, [-ocr] may not be
specified.
Ex) Updating firmware of the RAID Controller with resetting RAID Controller (RAID Controller number: 2).
raidcmd fwup –c=2 –f=C:\XXX.rom –ocr=yes
If blanks and parentheses are included in a absolute path, the path cannot sometimes
be recognized by the OS you use. Please confirm the specification of the specifying
absolute path of OS you use.
The value of “yes” in [-ocr] parameter are available with N8103-
176/177/178/179 RAID
Controllers. If you specified "yes", firmware of RAID Controller is updated without
restarting the system.
If a RAID Controller which is not supporting [-ocr] parameter is used, raidcmd fails when
specified "yes" in [-ocr] parameter.
If specifying "no" in [ocr] parameter, firmware of RAID Controller is updated after
restarting the system.
Step 3 If "fwup" command was executed, you cannot execute other function of Universal RAID Utility until update
firmware of RAID Controller is completed. If a message as "Please reboot the computer." was appeared after execution
the "fwup" command, please restarting the system to update firmware of RAID Controller.
> raidcmd fwup -c=2 –f=C:\XXX.rom –ocr=yes
Updating firmware...
Updating firmware and OCR(online controller reset)
completed.
>
2
3
114
- Universal RAID Utility 1
- User's Guide 1
- Introduction 4
- Contents 5
- Overview 10
- Windows Server 11
- Linux/VMware ESX 11
- Management PC 11
- System requirements 13
- Software (Linux) 14
- Software (VMware ESX) 14
- Resources 15
- Installation image 17
- Installation (Windows) 20
- Uninstallation (Windows) 23
- Log Viewer 32
- Standard and Advanced Modes 34
- Functions of RAID Viewer 36
- Battery 38
- Flash Backup Unit 38
- Disk Array 38
- SSD Cache Disk Array 39
- SSD Cache Drive 40
- Shortcut Menu 41
- Operation View 42
- Menu Bar 43
- [OFF] goes off the lamp 45
- Status Bar 46
- Functions of Log Viewer 47
- Log View 48
- Functions of raidcmd 50
- RAID System Configuration 51
- Configuration of RAID System 63
- Making Hot Spare 64
- About Dedicated Hot Spare 65
- Making Global Hot Spare 66
- Making Dedicated Hot Spare 67
- Removing Hot Spare 68
- Capacity of Logical Drive 75
- Items set for Logical Drive 75
- Number of Hot Spares 76
- Modes of Hot Spares 77
- Mode" 78
- Deleting Logical Drive 86
- Using CacheCade 87
- Capacity of SSD Cache Drive 89
- Deleting SSD Cache Drive 90
- Maintenance of RAID System 91
- Setting Patrol Read Priority 92
- Enabled) 93
- Disabled) 94
- Stopping Consistency Check 96
- Initializing Logical Drive 98
- Stopping Initialize 99
- Setting Initialize Priority 100
- Setting cache mode 101
- Rebuilding Physical Device 102
- Stopping Rebuild 103
- Setting Rebuild Priority 104
- Setting Power Saving Devices 105
- Setting Device Standby Time 106
- RAID Viewer 108
- To Online Forcibly 109
- To Failed Forcibly 110
- Step 1 Execute " 111
- Step 3 If " 111
- Scheduling Refresh Battery 113
- Troubleshooting RAID System 115
- Failure Detection Measures 116
- Windows 117
- Buzzer in RAID Controller 118
- Logical drive 121
- Physical device 121
- Physical device (Hot Spare) 121
- [Symbols] 121
- Physical Device 122
- [Online] 122
- Logical Drive 122
- Monitoring Battery Status 126
- Monitoring Enclosure Status 128
- Tree View of RAID Viewer 131
- Property of RAID Viewer 131
- Property of raidcmd 131
- ESMPRO Manager 132
- Using ExpressUpdate 135
- Utility 136
- Avoiding TCP port conflict 137
- Operation Environment 139
- OS Fatal Error Event 140
- RAID Viewer, Log Viewer 141
- Log Rotation 142
- NEC ESMPRO Manager 143
- RAID Controller 143
- Consistency Check 143
Relacionado con productos y manuales para Los controladores raid NEC Express5800/R120f-1M
Los controladores raid NEC N8103-89 Manual de usuario
(128 paginas)
(128 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.058 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales