NEC SigmaBlade AD106a Guía de usuario Pagina 130
- Pagina / 162
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
8-6 Troubleshooting
On-screen message Action
Multiple Single-bit ECC errors were detected during
the previous boot of the controller. DIMM on the
controller needs replacement.
If you continue, data corruption can occur.
Press 'X' to continue or else power off the system
and replace the DIMM module and reboot. If you
have replaced the DIMM please press 'X' to
continue.
Contact your service representative to
replace the RAID Controller.
Single-bit overflow ECC errors were detected during
the previous boot of the controller. DIMM on the
controller needs replacement.
If you continue, data corruption can occur.
Press 'X' to continue or else power off the system
and replace the DIMM module and reboot. If you
have replaced the DIMM please press 'X' to
continue.
Contact your service representative to
replace the RAID Controller.
Lamps
The Storage and I/O Blade, the drive carrier (hard disk drive), and the Blade Enclosure include
lamps to indicate the device status by a variety of colors and display patterns. See Chapter 2 for
locations of lamps and their indications.
Error Messages on Virtual LCD
The virtual LCD displays the error occurred during operation or DC OFF (AC power is being on).
The following table lists indications on virtual LCD, descriptions, and actions to take.
The Web console of the Blade Enclosure displays the status of the managed Storage and I/O Blade
on virtual LCD (16 digits x 2 lines). Refer to the User's Guide of EM card for how to use Web
console.
IMPORTANT:
Take a note on the messages displayed on virtual LCD before
consulting with your service representative. Alarm messages are
useful information for maintenance.
IPMI information is also useful for maintenance. Refer to the User's
Guide of CPU blade for how to collect IMPI information.
- NEC Express5800 Series 1
- Storage and I/O Blade AD106a 1
- User's Guide 1
- SAFETY INDICATIONS 3
- Attentions 4
- Prohibited Actions 4
- Mandatory Action 4
- Trademarks 6
- ABOUT THIS USER'S GUIDE 8
- IN THE PACKAGE 9
- CONTENTS 10
- Chapter 1 13
- SAFETY NOTES 14
- Do not step on the cable 15
- FOR PROPER OPERATION 17
- TRANSFER TO THIRD PARTY 19
- DISPOSAL AND CONSUMABLES 20
- USER SUPPORT 21
- Advice for Health 22
- Chapter 2 23
- OVERVIEW 24
- STANDARD FEATURES 25
- Front View 26
- Internal View 27
- External View 28
- Lamp Indications 30
- STATUS Lamp 31
- LAN (1 - 2) Link/Access Lamps 32
- DISK ACCESS Lamp 32
- Device Identification 34
- Chapter 3 35
- Check of MAC Address 36
- Installation Order 37
- SIGMABLADE-M 38
- Installing in Blade Enclosure 39
- Joint bracket for AD106a 42
- Installation and Removal 43
- IMPORTANT: 44
- Chapter 4 45
- RAID SYSTEM CONFIGURATION 46
- RAID Levels 49
- Removed physical drive 55
- Migration only 55
- Migration with addition 55
- Before Using WebBIOS 58
- Using WebBIOS 61
- Main Menu 62
- WebBIOS Menu 63
- Controller Properties 65
- How to change setting value 69
- Scan Devices 70
- Virtual Drives 71
- Physical Drive Properties 73
- 3. Click [Go] 73
- Configuration Wizard 75
- Controller Selection 75
- Physical View / Logical View 75
- Configuring Virtual Drive 77
- DG is added to Span 80
- Configure SPAN 85
- [Accept] 87
- Parameters for VD Definition 90
- Operation of Various Features 93
- Manual Rebuild 95
- Setting Hot Spare 99
- "DED HOTSPARE" 100
- Reconstruction 102
- Slow Initialize 105
- Number and ID 106
- Setting of Priority 107
- Chapter 5 109
- Setup of teaming 110
- Network Driver 111
- Optional Network Board Driver 111
- Setting WOL 111
- Setting Receive Side Scaling 112
- TCP Chimney Offload 113
- Receive-side Scaling 113
- NetDMA 113
- SETTING FOR SOLVING PROBLEMS 115
- UPDATING THE SYSTEM 118
- Chapter 6 119
- Chapter 7 121
- SYSTEM DIAGNOSTICS 122
- RELOCATING/STORING THE UNIT 123
- Chapter 8 125
- SYSTEM VIEWERS 126
- ERROR MESSAGES 127
- 8-4 Troubleshooting 128
- Troubleshooting 8-5 129
- Error Messages on Virtual LCD 130
- Troubleshooting 8-7 131
- 8-8 Troubleshooting 132
- SOLVING PROBLEMS 133
- Fail to power-off: 134
- Fail to start OS: 135
- Problems with Windows 137
- Server 2003 x64 Editions: 139
- Server 2003 R2 142
- COLLECTING EVENT LOG 146
- MAINTENANCE TOOLS 146
- Chapter 9 147
- ANTI-STATIC MEASURES 149
- PREPARATION FOR INSTALLATION 151
- Mezzanine Card 152
- Hard Disk Drive 157
- Appendix A 161
- A-2 Specifications 162
Relacionado con productos y manuales para Los controladores raid NEC SigmaBlade AD106a
Los controladores raid NEC N8103-89 Manual de usuario
(128 paginas)
(128 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.028 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales