NEC Express5800/320Lb Linux Guía de usuario Pagina 193
- Pagina / 296
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Maintenance 6-5
Cleaning the Floppy Disk Drive
A read/write error may occur due to stains on the read/write head of the floppy disk drive.
Use the cleaner dedicated for floppy disk drive to clean the read/write head. It is recommended to
clean the head on regular basis.
Cleaning CD-ROM
A dusty CD-ROM or dust-accumulated tray causes the device to fail to read data correctly.
Follow the procedure below to clean the tray and CD-ROM regularly:
1. Make sure that the server is powered (the POWER LED is lit).
2. Press the Eject button on the front of the CD-ROM drive.
The tray comes out.
3. Hold the CD-ROM lightly and take it out from the tray.
IMPORTANT: Do not touch the signal side of the CD-ROM with your hand.
4. Wipe the tray with a dry soft cloth.
IMPORTANT: Do not wipe the lens of the CD-ROM drive. Doing so may damage
the lens and may cause a malfunction of the drive.
5. Gently push on the tray front to close the tray.
6. Wipe the signal side of the CD-ROM with a dry soft cloth.
IMPORTANT: Wipe CD-ROMs from the center to the outside. Use only CD-ROM
cleaner if necessary. Cleaning a CD-ROM with record spray/cleaner, benzene, or
thinner causes damage to the CD-ROM contents. At worst, inserting the CD-ROM into
the server may cause failure.
- User's Guide 1
- SAFETY INDICATIONS 3
- Attention 4
- Prohibited actions 4
- Mandatory actions 4
- Trademarks 6
- To prevent voltage sag: 6
- PREFACE 7
- ABOUT THIS USER'S GUIDE 8
- Additional symbols 9
- Accessories 9
- CONTENTS 11
- Chapter 1 15
- WARNING LABELS 16
- Label A 17
- Label C 17
- Label B 17
- Label E 17
- Rack-mount Model 18
- Precautions for Use 1-5 19
- PCI/CPU Modules 20
- Precautions for Use 1-7 21
- PRECAUTIONS FOR SAFETY 22
- Precautions for Use 1-9 23
- 1-10 Precautions for Use 24
- Precautions for Use 1-11 25
- 1-12 Precautions for Use 26
- During Operation 27
- For Proper Operation 29
- TRANSFER TO THIRD PARTY 31
- ABOUT REPAIR PARTS 33
- Advice for Your Health 34
- Chapter 2 35
- STANDARD FEATURES 36
- syslog function 39
- In-service repairing 39
- Front View 40
- Front View (inside) 42
- CD- ROM Drive 43
- Rear View 44
- General Description 2-11 45
- CPU Module 46
- PCI Module 48
- Chassis Board Layout 49
- POWER LED 50
- BMC Status LED 50
- General Description 2-17 51
- 2-18 General Description 52
- Disk Access LED 53
- 2-20 General Description 54
- General Description 2-21 55
- 2-22 General Description 56
- General Description 2-23 57
- The CPU module has two LEDs 57
- DISK LED 59
- LAN Connector LEDs 61
- BASIC OPERATION 62
- Tabs Frame 63
- Power ON 64
- Power OFF 65
- POST Check 66
- Makes a beeping sound 68
- Floppy Disk Drive 69
- Use of Floppy Disk 70
- CD-ROM Drive 71
- Use of CD-ROM 72
- Chapter 3 73
- RAID by software 75
- How to Locate Failed Disks 76
- Chapter 4 83
- SYSTEM BIOS ~ SETUP ~ 84
- Starting SETUP Utility 85
- 4-4 System Configuration 86
- Configuration Examples 87
- Security 88
- Serial Devices 88
- Optional PCI–related devices 88
- Select Item 93
- Select Menu 93
- System Configuration 4-15 97
- Monitoring Configuration 97
- System Configuration 4-17 99
- “Disabled” 99
- IMPORTANT: 102
- System Hardware 103
- Save Changes & Exit 109
- Get Default Value 110
- Load Previous Values 110
- Save Changes 110
- SCSI BIOS ∼ FAST!UTIL ∼ 111
- Configuration Settings 114
- 00, 02, 04, 06, 08 115
- Scan SCSI Bus 118
- SCSI Disk Utility 118
- Select Host Adapter 118
- Reboot System 119
- Return to Fast!UTIL 119
- Exit Fast!UTIL 119
- FORCED SHUTDOWN AND CLEAR 120
- CHECK: 124
- Chapter 5 127
- NEC EXPRESSBUILDER 128
- NEC EXPRESSBUILDER Top Menu 130
- BIOS/FW/etc. Update 132
- Help 132
- Return to the Top Menu 132
- Consoleless Menu 133
- Menu Items 134
- Master Control Menu 135
- NEC ESMPRO Agent and Manager 136
- − Detection of server fault 137
- Detection of Server Fault 138
- Prevention of Server Fault 138
- Operation Window 142
- Data Viewer 143
- Alert Viewer 143
- NEC ESMPRO Agent 144
- Supplement 146
- NEC ESMPRO Manager 149
- General 150
- Maintenance 150
- Update 151
- DIMM 151
- PCI Device – General 153
- Detailed 157
- Electronics – General 160
- Electronics – Maintenance 160
- SCSI Slot – General 160
- SCSI Slot – Maintenance 161
- [Mirror Disk] 161
- 3. Start the tool 162
- ESMPRO 163
- Start and Stop of Components 164
- [CPU] module screen 167
- Main window 167
- 4. Start the component 169
- Firmware Update 171
- [CPU module] screen 173
- [Firmware Update] screen 173
- Dump Collection 174
- [CPU Module] – [Maintenance] 175
- Setup of System Operation 177
- 3. Click [Execute] 178
- BMC Firmware Update 179
- 2. Click [Update] 180
- Chapter 6 189
- DAILY MAINTENANCE 190
- Making Backup Copies 191
- Cleaning 191
- Mouse ball 192
- Mouse cover 192
- Rollers 192
- Cleaning Tape Drive 194
- SYSTEM DIAGNOSTICS 195
- Target scope 196
- Test window 196
- System bar 196
- Title bar 196
- OFF-LINE MAINTENANCE UTILITY 197
- System Information Viewer 198
- Chapter 7 201
- ERROR MESSAGES 203
- 7-4 Troubleshooting 204
- Troubleshooting 7-5 205
- 7-6 Troubleshooting 206
- Troubleshooting 7-7 207
- 7-8 Troubleshooting 208
- Troubleshooting 7-9 209
- 7-10 Troubleshooting 210
- Troubleshooting 7-11 211
- 7-12 Troubleshooting 212
- Troubleshooting 7-13 213
- POST Error Messages 214
- Troubleshooting 7-15 215
- 7-16 Troubleshooting 216
- Troubleshooting 7-17 217
- 7-18 Troubleshooting 218
- Troubleshooting 7-19 219
- Error Notification by BEEP 220
- Linux Error Messages 221
- 7-22 Troubleshooting 222
- SOLVING PROBLEMS 224
- ~ SETUP ~”.) 230
- Event Log 231
- Problems with NEC ESMPRO 235
- COLLECTION OF TROUBLE LOGS 236
- Dump switches 237
- Backup of IPMI Information 238
- Chapter 8 239
- SAFETY PRECAUTIONS 240
- ANTI-STATIC MEASURES 241
- 3.5-INCH HARD DISK DRIVE 243
- 8-12 System Upgrade 250
- CPU MODULE 251
- Removing CPU Module 252
- Release lever 253
- Latch lever 253
- Installing CPU Module 254
- Installing DIMM 258
- Removing DIMM 259
- Replacing DIMM 260
- PROCESSOR (CPU) 261
- Installation 262
- Pin marks 263
- Removing CPU 265
- Replacing CPU 266
- PCI MODULE 267
- Precautions 268
- Removing PCI Module 269
- Installing PCI Module 271
- 7. Close the release lever 272
- PCI BOARD 273
- Installing PCI Board 274
- Slots for inserting 275
- Bends for fastening 277
- 8-40 System Upgrade 278
- Removing PCI Board 279
- Replacing PCI Board 280
- Setup of Optional PCI Board 281
- N8104-84 1000BASE-SX Adapter 283
- 8-46 System Upgrade 284
- N8104-103 1000BASE-T Adapter 285
- 8-48 System Upgrade 286
- Delete LAN board setting 290
- 8-54 System Upgrade 292
- Example 292
- Appendix A 293
- A-2 Appendix A 294
- Appendix B 295
- B-2 Appendix B 296
Relacionado con productos y manuales para Servidores NEC Express5800/320Lb Linux
Servidores NEC Express5800/320Lc Guía de usuario
(357 paginas)
(357 paginas)
Servidores NEC Express5800/T110f-S Guía de usuario
(132 paginas)
(132 paginas)
Servidores NEC Express5800/GT110d-S Guía de usuario
(142 paginas)
(142 paginas)
Servidores NEC Express5800/120Rd-2 aviso
(14 paginas)
(14 paginas)
Servidores NEC Express5800/320Fd Guia de preparacion
(126 paginas)
(126 paginas)
Servidores NEC Express5800/320La Guía de configuración
(102 paginas)
(102 paginas)
Servidores NEC Express5800/320Ma Guía de usuario
(106 paginas)
(106 paginas)
Servidores NEC Express5800/320Lb Guía de usuario
(358 paginas)
(358 paginas)
Servidores NEC Express5800/120Rh-1 Guía de usuario
(232 paginas)
(232 paginas)
Servidores NEC Express5800/120Rj-2 Guía de usuario
(212 paginas)
(212 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.249 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales