NEC Express5800/340Hb-R Guía de usuario Pagina 251
- Pagina / 312
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Troubleshooting 7-7
"Display Settings" on the bottom-right of the window:
→ Select [Control Panel] – [Display] - [Settings] tab, and change the [Color quality]
to "Medium (16 bit)" or higher.
The screen turns blue during OS boot:
→ Wait for the period of time you set a BIOS [Boot Monitoring]; after the boot pair
is automatically swapped, the server will be rebooted and the OS will start up.
→ Start the OS from the other PCI module’s hard disk.
Fail to power off the server:
Is the POWER switch enabled?
→ Restart the server and start the BIOS setup utility.
<Menu to check: [Security] → [Power Switch Mask] → [Unmasked]>
POST fails to complete:
Is the DIMM installed?
→ At least four DIMMs are populated in the DIMM bank 0 for operation.
Is the memory size large?
→ The memory check may take a time if the memory size is large. Wait for a while.
Did you perform any keyboard or mouse operation immediately after you started the
server?
→ If you perform any keyboard or mouse operation immediately after start-up, POST
may accidentally detect a keyboard controller error and stops proceeding. In such
a case, restart the server once again. Do not perform any keyboard or mouse
operation until the BIOS start-up message appears when you restart the server.
Does the server have appropriate memory boards or PCI card?
→ Operation of the server with unauthorized devices is not guaranteed.
- NEC Express5800/340Hb-R 1
- User's Guide 1
- SAFETY INDICATIONS 3
- Attention 4
- Prohibited actions 4
- Mandatory actions 4
- Trademarks 6
- To prevent voltage sag: 6
- PREFACE 7
- ABOUT THIS USER'S GUIDE 8
- Additional symbols 9
- Accessories 9
- CONTENTS 10
- Chapter 1 15
- WARNING LABELS 16
- CPU Module 18
- PCI Module 19
- 1-6 Precautions for Use 20
- Expansion PCI Module 21
- 1-8 Precautions for Use 22
- PRECAUTIONS FOR SAFETY 23
- During Operation 28
- Rack-mount Model 29
- For Proper Operation 31
- 1-18 Precautions for Use 32
- TRANSFER TO THIRD PARTY 33
- ABOUT REPAIR PARTS 35
- 1-22 Precautions for Use 36
- Advice for Your Health 36
- Chapter 2 37
- STANDARD FEATURES 38
- Free area 41
- System with one CPU 42
- System with two CPU 42
- 2-8 General Description 44
- Rear View 45
- 2-10 General Description 46
- CD- ROM Drive 49
- Chassis Board Layout 51
- PCI Module Status LED 53
- LED Status / Action 54
- 2-20 General Description 56
- General Description 2-21 57
- 2-22 General Description 58
- Green Amber Status / Action 60
- General Description 2-25 61
- SMM Board Status LED 61
- 2-26 General Description 62
- General Description 2-27 63
- PCI Slot Status LEDs 63
- BASIC OPERATION 64
- Power ON 66
- Power OFF 67
- Power-On Self Test (POST) 68
- Floppy Disk Drive 71
- Insert/Remove Floppy Disk 72
- Use of Floppy Disk 73
- CD-ROM Drive 74
- Use of CD-ROM 75
- 2-40 General Description 76
- Chapter 3 77
- DISK OPERATIONS 78
- Disk Management 79
- Importing Data Disks 86
- Extending Data Volume Size 88
- Function 91
- Making disks duplex by RDR 93
- Dynamic disk 98
- How to Locate Failed Disks 101
- IMPORTANT: 105
- CHANGE DRIVE LETTER 109
- DUAL LAN CONFIGURATION 110
- 6. Click [OK] 112
- Removing dual LAN 113
- MODULES 116
- CONFIGURATION 123
- Chapter 4 125
- SYSTEM BIOS ~ SETUP ~ 126
- Starting SETUP Utility 127
- Advanced 132
- Peripheral Configuration 133
- Console Redirection 134
- Stratus 135
- Monitoring Configuration 137
- PCI OPROM hot key setup 139
- Security 140
- System Configuration 4-17 141
- Save Changes & Exit 143
- Get Default Value 144
- Load Previous Values 144
- Save Changes 144
- SCSI BIOS ∼ Fast!UTIL ∼ 145
- Configuration Settings 149
- – Sync Period 152
- Scan SCSI Bus 154
- SCSI Disk Utility 154
- Select Host Adapter 154
- Exit Fast!UTI 155
- Reboot System 155
- Return to Fast!UTIL 155
- RESET AND FORCED SHUTDOWN 156
- 4-34 System Configuration 158
- Chapter 5 159
- NEC EXPRESSBUILDER 160
- NEC EXPRESSBUILDER Top Menu 162
- Master Control Menu 165
- NEC ESMPRO Agent AND Manager 166
- Detection of Server Fault 168
- Prevention of Server Fault 168
- Operation Window 172
- Data Viewer 173
- Alert Viewer 173
- NEC ESMPRO Agent 174
- Supplement 176
- NEC ESMPRO Manager 183
- General 184
- Maintenance 184
- Update 185
- DIMM 186
- PCI Device – General 190
- PCI Device – Detail 190
- PCI Bridge – General 191
- PCI Bridge – Bus 191
- PCI Bridge – Detail 192
- Electronics – General 195
- Electronics – Maintenance 195
- SCSI Slot – General 196
- [Mirror Disk] 197
- [SCSI Slot] 198
- [General] 198
- [Alert report] 202
- ESMPRO 205
- Start and Stop of Components 206
- 4. Start the component 211
- Diagnostics 213
- [PCI Module] – [Maintenance] 214
- Firmware Update 216
- [CPU Module] – [Update] 217
- [CPU Module] 219
- Dump Collection 221
- [CPU Module] – [Maintenance] 222
- SCSI Bus Reset 224
- Setup of System Operation 226
- BMC Firmware Update 229
- 3. Click [OK] 230
- SMM Firmware Update 231
- Chapter 6 233
- DAILY MAINTENANCE 234
- Checking STATUS LEDs 235
- Making Backup Copies 235
- Cleaning 236
- Mouse ball cover 237
- Mouse ball 237
- Bottom View 237
- Test Items 239
- Test window 240
- System bar 240
- Title bar 240
- Target scope 240
- OFF-LINE MAINTENANCE UTILITY 241
- 6-12 Maintenance 244
- Chapter 7 245
- TO LOCATE THE ERRORS 246
- ERROR MESSAGES 247
- 1. Add a physical memory 248
- SOLVING PROBLEMS 250
- Is the DIMM installed? 251
- Is the memory size large? 251
- Is Shift pressed? 264
- Problems with NEC ESMPRO 265
- COLLECTION OF TROUBLE LOGS 273
- Collection of Event Logs 274
- 4. Click [Save] 275
- Preparing for Memory Dump 276
- Saving Dump Files 277
- 7-34 Troubleshooting 278
- Chapter 8 279
- SAFETY PRECAUTIONS 280
- ANTI-STATIC MEASURES 281
- OPTIONS 283
- 3.5-INCH HARD DISK DRIVE 284
- NOTES: 285
- 8. Slowly close the lever 288
- 1. Remove the front bezel 289
- PROCESSOR 291
- PCI BOARD 293
- SETUP OF OPTIONAL PCI BOARD 294
- Slots to install the board 297
- Installation of driver 297
- 9. Click [Finish] 299
- How to confirm the status: 300
- N8104-84 1000BASE-SX Adapter 301
- N8104-103 1000BASE-T Adapter 303
- 8-28 Option 306
- Appendix A 307
- A-2 Specifications 308
- Appendix B 309
- I/O Port Address 310
Relacionado con productos y manuales para Software de gestión de sistemas NEC Express5800/340Hb-R
(31 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.120 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales