NEC Express5800/S110R-1 Guía de usuario Pagina 61
- Pagina / 134
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Chapter 6: Advanced Chassis Setup
6-3
6-3 System Fans
Three 4-cm heavy duty counter-rotating fans provide the cooling for the Series3800/
S110R-1 (5015M-UR/5015M-U/5015M-NTR/5015M-NT). Each fan unit is actually
made up of two fans joined back-to-back, which rotate in opposite directions. This
counter-rotating action generates exceptional airfl ow and works to dampen vibra-
tion levels. It is very important that the chassis top cover is properly installed and
making a good seal in order for the cooling air to circulate properly through the
chassis and cool the components. See Figure 6-2.
System Fan Failure
Fan speed is controlled by system temperature via a BIOS setting. If a fan fails,
the remaining fans will ramp up to full speed and the Universal Information LED on
the control panel will blink quickly. Replace any failed fan at your earliest conve-
nience with the same type and model (the system can continue to run with a failed
fan). Remove the top chassis cover while the system is still running to determine
which of the fans has failed. Then power down the system before replacing a fan.
Removing the power cords is also recommended as a safety precaution.
Replacing System Fans
1. Removing a fan
After turning off the power to the system, fi rst remove the chassis cover and unplug
the fan cable from the motherboard. Unscrew the failed blower fan from the chassis
and pull it completely out from the serverboard.
2. Installing a new fan
Replace the failed fan with an identical 4-cm, 12 volt fan (p/n FAN-0086L). Push
the new fan into the vacant space in the housing while making sure the arrows
on the top of the fan (indicating air direction) point in the same direction as the
arrows on the other fans. Reposition the fan housing back over the two mounting
posts in the chassis, then reconnect the fan wires to the same chassis fan headers
you removed them from. Power up the system and check that the fan is working
properly and that the LED on the control panel has turned off. Finish by replacing
the chassis cover.
- Series3800/S110R-1 1
- Manual Revision 1.0d 2
- Release Date: April 15, 2008 2
- About This Manual 3
- Manual Organization 3
- Table of Contents 6
- Chapter 4: System Safety 7
- Chapter 7: BIOS 8
- Appendices: 9
- User's Manual 10
- Introduction 11
- Chapter 1 11
- 1-2 Serverboard Features 12
- 1-3 Server Chassis Features 13
- Chapter 1: Introduction 15
- System Block Diagram 15
- 1-4 Notes 16
- Chapter 2 17
- Choosing a Setup Location 18
- Rack Precautions 18
- Server Precautions 18
- Rack Mounting Considerations 19
- Installing the Inner Rails 20
- Installing the Outer Rails 21
- Chapter 3 27
- 27
- System Interface 27
- 3-3 Control Panel LEDs 28
- 3-4 SATA Drive Carrier LEDs 29
- Chapter 4 31
- System Safety 31
- 4-3 ESD Precautions 33
- 4-4 Operating Precautions 34
- Chapter 5 35
- Advanced Serverboard Setup 35
- Installing the Processor 36
- Installing the Heatsink 38
- Removing the Heatsink 38
- 5-3 Connecting Cables 39
- Connecting the Control Panel 40
- 5-4 I/O Ports 41
- 5-5 Installing Memory 41
- 5-6 Adding PCI Cards 43
- 5-7 Serverboard Details 44
- PDSMU Quick Reference 45
- 5-8 Connector Defi nitions 46
- NIC1 LED 47
- NIC2 LED 47
- Universal Information LED 47
- Fan Headers 49
- Serial Ports 49
- Universal Serial Bus 49
- Headers 49
- LAN1/2 (Ethernet Ports) 52
- Power LED 52
- 5-9 Jumper Settings 53
- 5-10 Onboard Indicators 55
- Floppy Connector 56
- IDE Connector 57
- SATA Ports 57
- Precautions 59
- 6-2 Control Panel 60
- System Fan Failure 61
- Replacing System Fans 61
- Removing the Front Bezel 62
- Accessing the Drive Bays 63
- SATA Drive Installation 64
- 5015M-UR/5015M-NTR 67
- Power Supply Failure 67
- 5015M-U/5015M-NT 68
- User's Manual 70
- 7-1 Introduction 71
- 7-2 Running Setup 72
- 7-3 Main BIOS Setup 72
- Main BIOS Setup Menu 73
- Main Setup Features 73
- 7-4 Advanced Setup 76
- XHardware Monitor Logic 85
- 7-5 Security 86
- 7-6 Boot 87
- 7-7 Exit 88
- Appendix A 89
- BIOS POST Messages 89
- Appendix B 95
- BIOS POST Codes 95
- Appendix B: BIOS POST Codes 97
- Appendix C 101
- RAID Confi gurations 102
- Intel Matrix Storage 102
- Creating a RAID 0 Volume 104
- Creating a RAID 1 Volume 105
- Deleting a RAID Volume 108
- Appendix D 111
- Managing Arrays 114
- Confi guring Disk Drives 115
- Creating Arrays 118
- Rebuilding Arrays 124
- Using the Disk Utilities 126
- Appendix E 131
- System Specifi cations 131
- Operating Environment 133
- Regulatory Compliance 133
© 2020, manymanuals.es. Todos los derechos reservados | 0.038 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales